06.19 www.demos‑trade.com 20 220240 V 20 220240 V 405183 15 W / 1,25 A 160 × 30 × 16 405184 30 W / 2,5 A 160 × 58 × 18 544903 50 W / 4,16 A 160 × 58 × 18 405186 75 W / 6,25 A 170 × 57 × 32 405187 100 W / 8,33 A 180 × 66 × 32 544904 150 W / 12,5 A 205 × 71 × 35 5 544898 24 W 63 × 42 × 37,5 >0,7 544900 36 W 82 × 48 × 33 >0,9 3 LIGHTING AND ELECTRIFICATION OF FURNITURE StrongLumio 12 V power supplies Principles for selection and installation StrongLumio S3 flat 12 V power supplies StrongLumio S1 12 V power supplies plug-in • for power supply of LED strips and lights with 12 V voltage, direct current, grey edges (12 V) • power supply: 220–240 V, 50 Hz • PF > 0.9 • overload, overvoltage, and short-circuit protection • for power supply of LED strips and lights with 12 V voltage, direct current • power supply: 220–240 V, 50 Hz • black adapter for direct plug-in connection • overvoltage and short-circuit protection • round connector on output • in order to achieve optimal function, it is recommended to have the power supply as close to the light source as possible (Longer cables cause voltage losses and a subsequent drop in luminous intensity. They may also have disturbing influence on nearby electrical appliances.) • power supply should have a minimum distance of 0.5 m from other electrical appliances • power supplies must be located in such a way that sufficient ventilation – heat dissipation, if located in a closed room, sufficient ventilation (ventilation holes) must be provided • cable length 2 × 1 m • round connector on output • in order to achieve optimal function, it is recommended to have the power supply as close to the light source as possible (Longer cables cause voltage losses and a subsequent drop in luminous intensity. They may also have disturbing influence on nearby electrical appliances.) • power supply should have a minimum distance of 0.5 m from other electrical appliances • power supplies must be located in such a way that sufficient ventilation – heat dissipation, if located in a closed room, sufficient ventilation (ventilation holes) must be provided • cable length 1 m Warning It is not possible to combine 12 V LED strips with a 24 V transformer and vice versa. The power supply must always have sufficient reserve for the respective LED strip set. During normal use, the reserve should be 20%, if used for more than 5 hours, we recommend increasing the reserve to 30% or more. Offered power supply have protection to prevent damage, the transformer switches off at overloading and after reducing the load and cooling, the power supply is functional again. However, overloading has a negative impact on the overall service life. The power supply should be installed in such a way that it can be accessed at any time for replacement and is well ventilated. Installation in small, unventilated space reduces its service life. Please note that the supply voltage must comply with ČSN EN 60038, damage due to over-voltage in the electrical network is not a reason for placing a complaint. Claims are resolved by replacing the faulty power supply. Additional costs associated with replacing the connection are not recognised. Power supply power (W) = x+ 20% (30%) x = LED strip length (m) × LED strip input power (W/m) Example: using a strip of 14.4 W/m and an installed strip length of 2.5 m, the strip power is 36 W + 20% reserve (7.2 W) = 43.2 W. You will therefore need a power supply with a minimum power of 44 W. code power L × D × H (mm) YEARS WARRANTY YEARS WARRANTY code power L × W × H (mm) PF
RkJQdWJsaXNoZXIy MzEyMDA=